| 1 |
Please read the manual carefully before using. |
| 2 |
Rinse off smudges, oil stains, or wax with detergent or thinner before applying any AD-COAT products. Not doing so will inhibit the ability of AD-COAT to permeate and adhere. |
| 3 |
Please wear think rubber gloves and eye protection
glasses while applying AD-COAT products.
Particularly, protect your eyes from the
product.
If in any case, the product gets into your eyes, rinse very carefully with water for more than 15 minutes, and consult a doctor.
|
| 4 |
Because it is an organic solvent, ventilation is required for indoor use. |
| 5 |
AD-COAT is classified as a hazardous material
under the fire code, so you must store AD-COAT
according to existing laws and regulations.
Do not use AD-COAT near open flame, and be extremely cautious with regard to open flame at all times while using the product.
|
| 6 |
Use stock solution, do not dilute with other solvents. |
| 7 |
Apply on a sample and test before using. |
| 8 |
When solvent evaporates, it starts to harden.
Here are time guidelines
for hardening:
| AD COAT |
1 |
2 |
3 |
| AD Super |
Approx. 10 hours |
More than 2 days |
Approx. 10 hours |
AD Super |
Approx. 24 hours |
More than 5 days |
Approx. 24 hours |
| AD White |
Approx. 10 hours |
More than 2 days |
Approx. 10 hours |
| AD Maintenance |
Approx. 6 hours |
More than 2 days |
Approx. 12 hours |
| AD Serazin |
Approx. 5 hours |
More than 7 days |
Approx. 10 hours |
| AD-SK Mortar |
Approx. 24 hours |
Approx. 24 hours |
Approx. 24 hours |
1,Time guideline
for surface hardening.
2,Time guideline for complete hardening.
3,Time guideline for storage of applied material
in a dry place
(must avoid water
or rain).
Conditions vary according to temperature, but strict observance is advisable.
|
| 9 |
Keep the product completely sealed in a cool
area that is below 30 degrees Celsius.
Particularly, be extremely careful not to
mix with foreign substances or water. |
| 10 |
Except when using the product the cap must be completely sealed when stored. |
| 11 |
Take out quantity needed and do not return the unused portion to original container. |
| 12 |
Avoid using AD-COAT with other company' products, doing so will interfere with AD-COAT's ability to permeate and adhere. |
| 13 |
After using any AD-COAT product, all tools and towels must be cleaned fully with thinner. |
| 14 |
After using any AD-COAT product, residue and thinner must be consigned to an industrial waste dealer as industrial waste. |
| 15 |
When applying AD-COAT before working on stone-pitching construction, wait more than 24 hours after applying it, and then work on the stone pitching. |
| 16 |
Refer to Safety Data Sheet (MSDS) for more information and detailed precautions for directions. |
| 17 |
Our products were developed and manufactured
for industrial use.
Therefore, if you are using the products
for medical or other use, please request
the experiment test at our company in advance
to ensure safety.
Make sure that the product does not enter the human body. Such usage is extremely hazardous, if there's the possibility that product residue will remain in the body, avoid such acts, DO NOT use the products for human body.
|
| 18 |
All experimental data in this catalogue is
originated from samples, which our company
produced using our own methods. Not the standard
values.
With regard to product improvements and changes,
indicated data might be changed without notice.
Request a trial to confirm that the product
suits your needs before using any of our
products. |
Contact number